Norm

ASTM B359/B359M - 18 en

Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins

58,09 70,29 Incl BTW

Over deze norm

Status Definitief
Aantal pagina's 11
Gepubliceerd op 01-10-2018
Taal Engels

1.1 This specification2 establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface for improved heat transfer.

1.2 The tubes are typically used in surface condensers, evaporators, and heat exchangers.

1.3 The product shall be produced of the following coppers or copper alloys, as specified in the ordering information.

Copper or
Copper Alloy
UNS No.

Type of Metal

 

 

C10100

Oxygen-free electronic

C10200

Oxygen-free without residual deoxidants

C10300

Oxygen-free, extra low phosphorus

C10800

Oxygen-free, low phosphorus

C12000

DLP Phosphorized, low residual phosphorus
(See Note 1)

C12200

DHP, Phosphorized, high residual phosphorus
(See Note 1)

C14200

DPA Phosphorized arsenical (See Note 1)

C15630

Nickel Phosphorus

C19200

Phosphorized, 1 % iron

C23000

Red Brass

C44300

Admiralty Metal Types B,

C44400

C, and

C44550

D

C60800

Aluminum Bronze

C68700

Aluminum Brass Type B

C70400

95-5 Copper-Nickel

C70600

90-10 Copper-Nickel

C70620

90-10 Copper-Nickel (Modified for Welding)

Copper or
Copper Alloy
UNS No.

Type of Metal

 

 

C71000

80-20 Copper-Nickel Type A

C71500

70-30 Copper-Nickel

C71520

70-30 Copper-Nickel (Modified for Welding)

C72200

Copper-Nickel

Note 1: Designations listed in Classification B224.

1.4 Units—The values stated in either in-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification.

1.5 Product produced in accordance with the Supplementary Requirements section for military applications shall be produced only to the inch-pound system of this specification.

1.6 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Sections 1, 12 and 18.

1.7 (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.)

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Details

ICS-code 23.040.15
Nederlandse titel Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins
Engelse titel Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins
Vervangt

Winkelwagen

Subtotaal:

Ga naar winkelwagen