Norm

ASTM D3965 - 11 en

Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings

  • Deze norm is ingetrokken sinds 01-09-2016

45,11 54,58 Incl BTW

Over deze norm

Status Ingetrokken
Aantal pagina's 4
Gepubliceerd op 01-09-2011
Taal Engels

1.1 This classification system covers materials made from only virgin ABS polymers and blends of ABS polymers suitable for use in the extrusion of pipe and molding of fittings.

1.2 The requirements of this classification system are applicable only to the ABS polymers and blends of ABS polymers as classified and do not address the requirements of the finished pipe or fittings. The applicable ASTM standard specification for pipe or fittings shall be consulted for their requirements.

1.3 This classification system excludes ABS polymers and blends of ABS polymers made from reprocessed, regrind, reclaimed, or recycled materials. ABS rework, generated in-house by the original plastic manufacturer, may be used by that original manufacturer, provided the ABS product shipped meets the physical and mechanical properties required by its callout in Table 1.

1.4 This classification system and subsequent line callout (specification) provides a means for describing ABS materials used in the manufacture of pipe and fittings. It is not intended for the selection of materials. Material selection shall be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than those covered by this classification system, and the economics.

1.5 This classification system and subsequent line callout (specification) provides for the classification of ABS polymers and blends of ABS polymers into groups based on five properties: Izod impact strength at room temperature, Izod impact strength at low temperature, deflection temperature under load, tensile stress at yield point, and modulus of elasticity in tension. The properties included are those required to identify the ABS material by the cell classifications.

Note 1—Other requirements necessary to identify particular characteristics of ABS polymers and blends of ABS polymers will be added as test methods become available or the need is identified.

Note 2—Due to pipe and fitting standards requirements a separate standard is planned for recycled materials.

Note 3—This classification system and ISO 7245-1984 are not equivalent.

1.6 The values stated in SI units shall be the standard. The values given in parentheses are for information only.

1.7 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this classification system:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Physical Property Requirements for ABS Pipe and Fitting Materials

Note—The minimum property value for any material will determine the cell number although the maximum expected value may fall within the next higher cell.

ASTM
Test Method
Cell Limits
012345
Izod impact, min:D256, Test Method A, Cantilever Beam (Izod-Type) Test
at 23°C (73°F), J/mA110 160 210 320 430
(ft-lbf/in. of notch)A(2)(3)(4)(6)(8)
at 30°C (22°F), J/mA50 110 160 210 270
(ft-lbf/in. of notch)A(1)(2)(3)(4)(5)
Deflection temperature under load,
min, 1.82 MPa, (264 psi)
annealed, 3.18 mm (0.125 in.)
thickness:
D648
°CA76 82 88 93 99
(°F)A(170)(180)(190)(200)(210)
Tensile stress at yield point, min:D638
MPaA24 31 38 45 52
(psi)A(3500)(4500)(5500)(6500)(7500)
Modulus of elasticity in tension,
min:
D638
MPaA1380 1650 1930 2210 2480
(psi)A(200 000)(240 000)(280 000)(320 000)(360 000)

A Unspecified.

Details

ICS-code 23.040.20
Engelse titel Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
Vervangen door

Winkelwagen

Subtotaal:

Ga naar winkelwagen